ATIKA BKS 38 - Betreibershandbuch PDF herunterladen (Seite 21)

 Never leave the saw running unattended.

 This petrol chain saw produces harmful substances!

Never run the chain saw in closed or poorly ventilated

rooms. Provide for a sufficient change of air when working in

wells, trenches or confined spaces. There is the risk of

carbon monoxide poisoning or death by suffocation.

 Immediately stop working when you feel unwell (e.g.

headache, dizziness, nausea, etc.). Otherwise there is an

increased risk of accidents.

 Â When switching on the chain saw must be supported

and held safely. Chain and guide bar must stand free.

 Start cutting only when the saw chain has reached the full

number of revolutions.

 Do not overload the machine! You work better and safer in

the given performance range.

 Do not use the chain saw for lifting or moving of wood.

 Make breaks when sawing so that the engine can cool

down.

 Do not place a hot chain saw in dry grass or onto inflam-

mable objects.

 Never touch the silencer and the engine while the saw is

running or shortly after it was stopped. Danger of burning!

 Never get in contact with the running saw with metallic

fences or the ground.

 Make sure that the wood is free of foreign object (stones,

nails etc).

 Make sure that the wood can not turn when sawing.

 Saw splintered wood with care. There is risk of injury by

wood pieces carried away.

 Avoid saw backstroke by a correct guiding of the saw.

 Note: Safety instructions - saw backstroke

 Â Use the claw stopper (31) for fixing the chain saw on

the wood. Use the claw stopper when sawing as lever.

 Do not use the chain saw for lifting or moving wood.

 Let the chain saw work by producing a light leverage

pressure over the claw stopper.

When sawing do not press

with strength.

 When sawing thicker perches or trunks set back the claw

stopper (31) on a deeper point. For setting back release the

claw stopper from the wood and place it again in a deeper

position. Do not remove the saw here out of the cut.

 Be careful at the end of a sawing cut. As far as the saw

leaves the wood the force of weight changes.

There is risk

of accident for legs and feet.

 Remove the chain saw only with running saw chain out of

the cut.

 If the saw chain gets jammed in the wood, stop it

immediately. Use a wedge to free the guide bar.

Safety instructions - saw backstroke

 What is saw backstroke? Saw backstroke is the

sudden strike upwards or backwards of the

running chain saw in direction of the operator.

This happens when

− Â

the guide bar tip gets in contact with the sawing

material (unintended) or other hard objects.

− the saw chain is jammed at the guide bar tip.

The chain saw reacts uncontrolled and causes frequently heavy

injuries with the operator.

Carry out lateral cuts, diagonal cuts and longitudinal cuts

with increased attention because here the claw stopper (36) is

not put on.

How to avoid saw backstroke?

 Â Always hold the chain saw firmly with both hands.

 Â For better control saw with the lower edge of the

guide bar. Hold the chain saw as close as possible to the

horizontal position when contacting wood.

 Â Never saw with the guide bar tip.

 Â Sawing with the upper guide bar edge may cause a

saw backstroke if the saw gets jammed or hits a hard object

in the wood.

 Start cutting only with running saw chain.

 Only work with sharp and correctly sharpened saw chain.

 Only work with correctly clamped saw chain.

 Â Use claw stopper (31) as lever.

 Never work above height of shoulders.

 Never cut through several perches at the same time. When

releasing make sure that no other perch is touched.

 Â If possible use a sawhorse when cutting to length.

 Stab cuts shall only be carried out by instructed personal.

General safety instructions

 Stop the machine when:

− contact of chain saw with soil, stones, nails or

other foreign substances

B Check immediately chain and guide bar.

− carrying out repair works

− maintenance and cleaning

− removal of faults

− transport

− clamping again the chain

− chain change

− Leaving the machine (also during temporary inter-ruption)

 Maintain your chain saw with care:

− Comply with the maintenance instructions and the

advices for lubrication and for the tool change.

− Keep your tools sharp and clean in order to be able to

work better and safer.

− Keep the handholds dry and free from resin, oil and

grease.

 Check the machine for possible damage:

− Carefully check the machine, in particular after it has been

dropped.

− Before continuing to use the machine, the protective

devices must be inspected to ensure that they work

perfectly and with their intended function. Only operate the

machine with complete and correctly attached safety

equipment and do not alter anything on the machine that

could impair the safety.

− Check whether the movable parts function perfectly and

do not stick or whether the parts are damaged.

All parts

must be correctly installed and fulfil all conditions to

ensure perfect operation of the saw.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 151 152

Kommentare zu diesen Handbüchern

Keine Kommentare

ATIKA BKS 38 - Betreibershandbuch Seite 21

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kraftkettensägen ATIKA BKS 38 -